Mechanical Electrical Plumbing Training


MEP Engineering deals with Mechanical, Electrical and Plumbing systems which have a vital role in the building construction industry. The Mechanical aspect focuses on Heating, Ventilation and Air Conditioning (HVAC), whereas the Electrical aspect focuses on supplying power to all the services in a building including lighting, appliances etc.& Plumbing part usually deals with water distribution and drainage systems, CP & Sanitary fixtures orientation design, waste water treatment process and fire fighting systems. Plumbing is to deliver hot and cold water it is also known as PHE (Public Health Engineering).
There is a huge demand for skilled MEP Professional workforce on enormous projects like Residential, Commercial , Airport, schools, hospitals, malls, etc.

HVAC-R

  • As per ASHRAE and ISHRAE Standards
  • Modes of Heat Transfer
  • Sensible Heat and Latent Heat
  • Basic Components of Air-Conditioning and Refrigeration machines
  • Fundamental of Ventilation system(fresh & exhaust)
  • Classification of Air-Conditioning System
  • Classification of Refrigeration System
  • Basic Refrigeration System or Vapor Compression Cycle
  • Heat load calculation & Psychometric chart
  • Pressure Enthalpy Chart
  • Legends and Symbols used in the HVAC Industry
  • Schematic drawing for HVAC-R
  • Fundamental of Compressor,Condenser,Expansion Valve & Evaporator
  • Refrigerant and Brines
  • Normal, Split, cassette and VRV, chiller, AHU
  • Pipe  Selection & Sizing.
  • Pump head calculation
  • Static Pressure Calculation
  • Load Calculations (Manually using E-20 form)
  • ESHF, ADP & Air Flow Rate (CFM) Calculation
  • Selection of Motor HP
  • Selection Fan/Blower RPM
  • Selection of Pump
  • Temperature difference (ΔT) Calculation
  • Ventilation requirement for IAQ
  • Calculation of ‘U’ Factor
  • Diversity factor
  • Humidity Ratio
  • Damper’s
  • Dry Bulb ,Wet Bulb & Dew Point Temperature
  • Cooling and Dehumidification
  • Heating and Humidification
  • Air Distribution System
  • Duct Design consideration
  • Duct sizing as per Aspect Ratio
  • Calculation of Number of sheets for Duct
  • Gauge selection for Sheet Metal
  • Selection of Diffusers and Grilles
  • Duct sizer for Duct sizing
  • Duct Materials and Insulation materials used in HVAC Industry
  • Duct Routing – Preparation of single line diagram (SLD)
  • Preparation of Layouts (Double line Diagram – DLD) as per SMACNA rules
  • Openings for Ducts passing through Wall
  • Concept of CAV & VAV
  • Hydronic System
  • Classification of Water Piping
  • Pipe sizing for chill water system
  • Fittings used in the HVAC Piping System
  • Valves used in the HVAC Piping System
  • Openings for CHW Pipes passing through Wall
  • Trox CAD Base for Diffuser & Grilles
  • Fire Protection & Safety consideration.

Electrical System

  • International Electrical Codes, Standards and Regulations
  • Electrical Generation, Transmission and Distribution
  • Electrical Legends and Symbols
  • Preparation of Single Line Diagram
  • Electrical Load Estimatation .
  • Total Connected Load and Maximum Demand Calculation
  • Load Distribution Schedule and Load Balancing Calculation
  • Major electrical loads(Lighting load – Internal & external,Utility
  • power load,HVAC loads like Chillers, AHU’s, FCU’s, Pumps, Fans etc,
  • PHE & FF loads like Water transfer pumps, Booster pumps, Fire
  • Fighting pumps, Jockey pumps etc, Lifts (Elevator) load, Computer &
  • data centre (Server) loads for office building.
  • Basics of Transformer & Sizing Calculation
  • Basics of Diesel Generator Sizing Calculation
  • Lighting System & Lux Level Calculation
  • Sizing of UPS/Inverter& Battery banks
  • Capacitor Bank Selection
  • Battery Bank Selection
  • Busbar Selection and Sizing
  • Fault Level Calculation
  • Short circuit calculation
  • Voltage drop calculation
  • Fundamental of Earthing System & Sizing Calculation
  • Fundamental of Lightning Arrestor & Sizing Calculation
  • Fire Detection and Alarm System
  • Public Addressing System
  • Closed Circuit Television (CCTV)
  • Different Entities of Illuminating System
  • Introduction to Electric Motors, Drives and Starters
  • Fundamental of Electrical Motors & Pumps system
  • Motor control centers (MCC’s)
  • HT & LT Cable Selection, Sizing & Calculation
  • Determining Cable Trays and Trenches
  • Cable trays,trunking or raceways, conduits system
  • Basics of Distribution boards (DB’s)
  • Preparation of cable & DB schedule
  • HV/LV switches gears
  • Selection of Switches and Sockets
  • Isolators, Bus ducts ,switch board & socket outlets
  • Selection of Automatic Main Failure Panel
  • Fundamental of Electrical Panels(HT/LT)
  • Basics of Power Factor Correction and APFC Panel

Plumbing System

  • Plumbing Systems As per NBC and UPC
  • Fundamentals of Plumbing System
  • Fixtures, Fixture fittings & Faucets
  • Fixture Materials & Fixture Clearances
  • Plumbing PHE
  • Underground Sump(UGS) sizing
  • Elevated storage Reservoir(ESR) sizing
  • Over Head tank distribution system
  • Flow rate (q) & Loading Unit (z) – From Probability equation
  • Hazen Williams Formula for Head Loss Calculation
  • Number of tapping to be connected in Bigger Diameter Pipe
  • Number of Population served
  • Single stack (partially ventilated) system
  • Plumbing of Bath Tub, Kitchen sink, Water Closet, Bidet, wash Basin,
  • Water Closet,Bath,Tub,Shower,Urinals,Kitchen Sink,Floor Drain
  • Pumping System & selection
  • Pumping Calculations – HP/Watts
  • Hydro-pneumatic system
  • Piping and Tubing
  • One/Two Pipe System
  • Piping fitting assembly
  • Pipe Joining methods & Pipe Support
  • Insulation of pipes
  • Industrial  valves & Components
  • Calculating Depth of Inspection Chamber/ Manholes
  • Estimation of water demand using hunter curves
  • Pressure drop and velocity limitation method
  • Water Supply system & Water cycle
  • Sizing of water supply for high rise buildings
  • Domestic Water Supply and Distribution System
  • Water Demand Calculations
  • Water Storage Calculations
  • Water Purification & Treatment methods
  • Classification of water Heaters
  • Hot Water Supply system
  • Hot water distribution inside the building
  • External Water Supply & Pipe Sizing Calculations
  • Internal Water Supply & Pipe sizing calculations
  • Material used in External/Internal water supply system
  • Schematic Layout of Water Treatment Plants
  • Schematic Layout of Sewage Treatment Plants
  • Internal Sanitary Drainage Pipe Sizing Calculations
  • External Sanitary Drainage Pipe Sizing Calculations
  • Storm water management
  • Storm Water Drainage Pipe Sizing Calculations
  • Water Supply Schematic Layout
  • Sanitary Drainage Schematic Layout
  • Requirements of Sanitary Drainage System
  • Material used in Sanitary Drainage system
  • Calculation of Slope by Manning’s formula
  • Continuity Equation, Manning’s Formula and Rational Formula

Scope:- After successfully completing this course students can establish a career in mechanical maintenance among various manufacturing and automation industries like food & Beverages, Oil and Gas, Power Plants, Manufacturing Process, Chemicals, Power Generation, Water/Waste Water Treatment, Aerospace, Automotive, Fabricated Metals, Packaging Process, Metals and Mining’s etc.

Category:- 100% Job Oriented MEP Course

Course Duration:– 3 Months

Empty tab. Edit page to add content here.

Course Registration